|Raw Material:||PTFE||Type:||Water Base|
|Application Method:||Spray||Usage:||Appliance Paint, Electrical Insulating Varnish|
water based teflon coating,
teflon non stick coating
PTFE Non Stick Coating / Three-Layer Spray / Water Base Non-Stick Coatings
Techyours® is designed with two-layer coating system. Thanks to its high density, good inadhesion, easy-to-clean performance and strong practicability. It is applicable for substrates like aluminum, alloy and stainless steel etc.
It is Water based Three-layer Marble-Coating (Moss style). It is widely applied to internal coating of non-stick kitchenware such as aluminum-made frying pans, woks, stockpots, electric stewpots, electric bake wares and cake molds.
Type of PTFE Coating
Main Features of PTFE Coating
l Excellent heat resistant
l Excellent chemical resistance and abrasive resistance
l Excellent and lasting non-stick performance, easy to clean
Data List of Techyour PTFE Coating
|Solid content (%)||35±1|
|Density (g/ml)||1.20 Primer/1.30 Top|
|pH||8-11(Primer and top)|
|Color of the film surface||8-11(Primer and top)|
|Curing temperature (℃)||380-420|
|Gloss (60° glossimeter)||10-20|
|Film thickness (μm)||20-30|
Non-stick performance Fry eggs at 170±10℃
Corrosion resistance Boling 10% salt water for 24 hours
|Abrasion resistance 3KG/21cm2||>3000 cycles|
|Hardness (ZHONGHUA pencil)||>H|
Main Processing Way of Techyour PTFE Coating
1. Requirement on pre-treatment
l Firstly, apply high-temperature degreasing, then wash with 1%~3% NaOH solution (60℃) for more than 6 minutes, dry it after water rinsing;
l Blast with 80#~120# corundum to make the surface roughness reach 2.0μ~3.0μ, pay attention to sandblast evenly;
l Wash with 1%~3% NaOH solution(60℃) for more than 6 minutes, rinse with water;
l Wash with 1%~3% hydrochloric acid solution (60℃) for more than 6 minutes, rinse with water and dry.
2. Preparation of the coating
l Dispersion of coating: the coating must be fully dispersed before operation;
l Viscosity adjustment: the viscosity could be adjusted according to different spray methods. Dilute with clean water if the viscosity is over high;
l Coating filtration: filtrate the coating with screen (100mesh) before using.
l The spraying environment should be dry, well-ventilated, no smoking and fire. We suggest using dedicated spray gun, elevated tank and curing oven;
l The air compressor should be degreased, dewatered and equipped with water oil separator before using;
l Roll the coating at 30rpm speed before using to make sure there is no sediment, and filter with 100 mesh screen;
l Adjust atomization and oil pump capacity of the spraying gun; make sure the unit is clean and flat;
l Preheat the substrate to 35℃ and spray the primer. Dry it at temperature of 120℃~150℃ for 10min-15min. Keep the thickness of primer within 12μm-18μm;
l Spray top coating after the primer is dry and cooling to room temperature, then spray the top. Dry the unit at the temperature of 100℃~150℃ for 10~20 min, and gradually increase the temperature to 380℃~420℃. Keep for 10 min. Keep the thickness of top coat within 10μm~12μm. The thickness of two coat tally should be between 20μm~30μm;
l The oven (or the tunnel drier) must be well ventilated; otherwise, it will lead to color change of coating.
Main Application of Techyour PTFE Coating
Techyours® PTFE non-stock coating must be stored under frost proof environment under optimum 18-26℃ temperature;
It should be homogenized once or twice a month by gentle rolling or stirring when storing or before using,90min per time.
Techyours® PTFE non-stock coating is package in 25L PE drum with 25kg(55lb) content.
Before processing, please read the Materials Safety Data Sheet carefully. You could find them from www.everflon.com, or contact us +86-27-84888055 or our local service center, you also should could scan the QR code which on the package to download by your Smartphone.